2017年 07月 16日
キャトルに必要な数値、 http://laffhog.com/renault/renault4.html |
Renault 4 | |
Models: R. 1123 Estate Car; R. 2106 7.cwt. Van ENGINE (At front) 1 Type (800 01) ... 4 stroke; over head valves; side camshaft 2: Cooling system ... Water pomp, radiator (9.25lb./in.sq)fan 2a. and thermostat (82°C). Sealed system; 2b. clean and refill every 27,000 miles or3 years 3. Number of cylinders ... 4 (wet liners) 4. Firing order and idling speed 1 3 4 2(No.1 by flywheel)625/675 r.p.m. 5. Bore . ... 58mm. (2.283in.) 6. Stroke ... ... 80mm. (3.150in.) 7. Cubic capacity ... 845c.c. 8. Compression ratio and 8:1; 6.5 to 9.5 Kg./cm.sq(92 to 135lb./sq.in 9. Brake horse power(S.A.E.) 30 at 4,700 r.p.m. 10 Torque (S.A.E.) ... 45lb.ft. at 2,300 r.p.m. 11: Piston oversizes ... Matched piston and liner sets 12. Piston clearance . As number 11 13. Piston rings number 2 Compression' 1 oil ('Uflex') 14. Piston rings width ... Compression, 2mm.; oil, 3.5mm. 16. Piston rings gap Supplied preset with piston and liner kit(in bore) 17 Oil pressure 43lb./sq.in. at nominal engine speed 18. Gudgeon pin diameter 16mm. 19. Gudgeon pin fit in piston Clearrance 20. Gudgeon pin fit in con. rod Interference 21 Crankpin diameter ... 38mm 22: Crankpin undmizes ... 37.75mm. 24. Big end bearings ... Aluminium tin, thin shell 25. Big end bearing clearance .015 to 054mm. (.0006 to .0021in.) 26. Big end side clearance ... .05 to .15mm. (.0019 to .0059in.) 27 Main journal diameter ... 40mm. 28: Main journal undersizes ... 39.75mm. 29. Main bearings ... ... 3; aluminium tin, thin shell 30. Main bearings length ... (1) 33mm.;(2)30mm.; (3) 27mm. 31. Main bearing clearance... .009 to .048mm. (.0003 to .0019in.) 32. Crankshaft end float ... .05 to 25mm. (.0019 to .0098in.) 33. Crankshaft end thrust on Centre main bearing 34. Camshaft journal dia. 38mm. 35. Camshaft bearings 3 (machined in block) 36. Camshaft bearing cl'nce .025 to .075mm. (.001 to .0029in.) 37. Camshaft end float ... .06 to .145mm. (. 0024 to .0057in.) 38. Camshaft drive type Chain; 64X9.525mm. pitches; width,5.75mm 39. Valve head diameter ... Inlet 28.2mm.(1.11in,)exhaust,25mm(0.984in,) 40. Valve stem diameter ... 7mm. inlet and exhaust 41. Valve seat angle ... 45° inlet and exhaust 42. Valve lift ... ... Inlet, 5.75mm. (0.226in.)exhaust,6mm(0.236in.) 43. Valve guide length ... 35mm. inlet and exhaust; 14mm. above head 44. Valve stem/guide cl'nce Inlet, .010mm. to .069mm. (.00039 to.0027in.); 44a. exhaust, .020 to .084mm.(.0008 to .0033in.) 45. Valve spring free length 40.4mm. (1.591in.) Het and exhaust 46. Valve spring rate Length 24mm. (0.945in.) under load of 22kg. (48,5lb.) 47. Valve working clearance Inlet, 0.15mm. (.006in.); exhaust,0.20mm(.008in.)cold 49. Valve timing .Inlet opens 60° B.T.D.C.; closes 30°A.B.D.C 49a. Exhaust opens 45°B.B.D.C.;closes 70° A.T.D.C. 50. Petrol pump ... ... Guiot mechanical 51. Carburettor ... ... Zenith W5.069 52. Choke tube ... ... 20 53. Mainjet ... ... 90 54. Compensating jet ... 110x70 55. Pilot jet ... ... 40 62. Needle valve ... 1.6mm. TRANSMISSION 101. Type ... ... Front wheel drive 102. Clutch Ferodo, 6.250in. diameter, diaphragm type 160 D.B.1.R. 103. Gearbox 4 forward speeds, all synchromesh (type 334) 105. Gearbox ratios Top, 1.03:1; 3rd, 1.36:1; 2nd, 2.053;Ist and R: 3.80:1 107. Driving axles .. Open shaft, constant velocity universal joints 108. Final drive gear ... Spiral bevel 109. Final drive ratio ... 4.125:1 110. Number of gear teeth ... Crown wheel, 33; pinion, 8 111 ' Crown wheel/pinion b/lash 0. 12 at 0.25mm. (.0047 to .0098in.) 113. Differential brg. pre load New, 2 to 3.5kg. (4.4 to 7.7lb.) 114. at housing diam., oil seal on; refitted, free without play BRAKES (Single circuit) 201. Front ... Lockliced hydraulic, drum type: R4 201a. and R.4L, 200mm. (7.87in.); Van, | 201b. 228.5mm. (9.0m.) 202. Rear ...Lockheed hydraulic; 160mm. (6.3in.)drums 203. Handbrake ... ...Cable on front wheels 204. Linings fixint ... ...Ferodo: 238/187x35x4.5mm.;Van, 204a. 2441189 x 40 x 4.5min. 205. Linings rear ... ... Ferodo, 152/118x25x4.5mm. STEERING (see also " Dimensions") 301. Type ... ... ... Rack and pinion 302. Camber angle ... ... 0° to 1° 303 ' Castor angle ... ... 9° to 11° (adjustment by tie bars) 304. King pin inclination ... 13° 305. Wheel alignment (front) 0 to 4mm.(0.157in.)toe out at wheel rim flange 306. Conditions for checking... Laden at front FRONT SUSPENSION 401. Type Torsion bar and wishbone R.4 & RAL Van 402.Torsion bar diameter 16.54mm. (0.65in.) 17mm. (0.669m.) 403..Working length ... ............ 1030mm. (40.55in.) REAR SUSPENSION 501. Type ... ... Torsion bar, telescopic shock absorbers, 501a. trailing arms; (anti roll bar on Van) 502. Wheel camber ... ... 0° to 1° 30’ 503. Toe in ... ... 0 to 6mm. (0.236in.) Torsion bar diam., 20.5mm. (0.807in.) working length, 0.800 metre (31.5in.) ELECTRICAL SYSTEM 601. Ignition timing (static) ... 0 ± 1mm. before/after T.D.C. (T.D.C. 601a. [also for stroboscope] mark on flywheel) 602. Sparking plugs A.C. 43FS, Marchal 36, Motorcraft AE32 or Champion L87Y 603. Sparking plug gap ... 0.6 to 0.7mm. (.024 to .028in.) 604. Distributor ... S.E.V., type R252 curve 605. Contact breaker gap 0.4 to 0.5mm(.016 to.020in.)dwell angle,57° ± 3° 606. Centrif. adv. starts at 500 r.p.m. Distributor degrees and rpm 607. Centrif. advance max 14° at 1800 r.p.m. 610. Ignition coil ... ... S.E.V. or Ducellier, high voltage, oil filled 611. Battery ... ... Fulmen, type AS.809; 12v. 30 ah. 612. Battery earth ... .. . Negative 613. Dynamo ... ... Ducellier, type 7346A; 22amp. 614. Control box ... ... Ducellier, type 8311 A, drop off, 9. 6v. 615. Starter motor ... ... Ducellier, type 6185. Lock torque, 616. 6lb.ft.; current draw, 300amp, CAPACITIES 701. Engine sump ... ... 4.5 pints 702. Gearbox ... 2pints 703. Differential ... ... 2 pints 704. Cooling system ... 9 pints with heater 705. Fuel tank ... 5.750 gallons 706. Tyre size ... ... 135 x 330 radial 707. Tyre pressures R4 & R4L F.19; R.23(Full load: F,21;R.,26) 707a. (lb.lsq.in.) Van, F 18; R,24 (Full load: F.19; R.27) 708. No. of grease gun points .. . None 709. Normal servicing intervals Engine oil change 3,000 miles* 710. Hydraulic fluid ... ... Lockheed (S.A.B. 50 R3) 711. *Diagnostic maintenance at least annually or every 6 9,000 miles DIMENSIONS R4 R4L Van 801. Length overall ... ... 12ft.0in. 12ft.0in. 11ft. 10in. 802. Width overall ... 58.5in. 58.5in. 60in. 803. Height overall (unladen) 61in. 61in. 68in. 804. Weight ... ... 1411lb. 1455lb. 1433lb. 805. Ground clearance (min.) 5in. (front suspension) ......... 806. Track ... ... .. 49in. front and rear ......... 807. Wheelbase N/S, 94.250in.; 0/S, 96in. 808. Turning circle diameter ... 32ft. 7in. (kerbs) TORQUE SPANNER DATA (lb.ft.) 901. Cylinder head nuts (cold) 39/47 902. Big end bearing nuts ... 22/25 903. Main bearing nuts ... 39/47 905. Flywheel bolts ... ... 25/29 906. Clutch to flywheel bolts .. . 8 907. Drive pinion bearing nut 30/45 908. Crown wheel bolts ... 75 BODY AND CHASSIS 1001. Type of construction Welded and bolted panels on box section platform 1002. Material of body panels Steel 1003. Windscreen glass ... Toughened Note The engine must not be run with a plug lead disconnected unless the lead is earthed. |
by HyperMoto
| 2017-07-16 10:40
| キャトルに必要な数値